1. Aonad scriú socraithe a fheistiú :
a. Seiceáil cruinneas an seafta
Sula gcuirfidh tú an t-aonad imthacaí suas, seiceáil cruinneas an seafta gan aon lúbadh, burrs agus lochtanna eile.
seiceáil cruinneas an seafta
b. Scrúdaigh dolúbthacht agus cothrom an dromchla gléasta
Caithfidh dromchla gléasta an mheaisín a bheith docht go leor, agus caithfidh an dromchla gléasta a bheith chomh réidh agus chomh réidh agus is féidir. Flatness: Max0.15mm (tá 0.05mm níos úsáidí).
Scrúdaigh dolúbthacht agus cothrom an dromchla gléastaScrúdaigh dolúbthacht agus cothrom an dromchla gléastaScrúdaigh dolúbthacht agus cothrom an dromchla gléasta

c. Suiteáil aonad imthacaí
Seachain an t-imthacaí a bhualadh le casúr chun an t-imthacaí a bhrú ar an seafta , má thugann tú tionchar láidir ar dhromchla taobh an fháinne istigh, bogann an slinger, agus d’fhéadfadh sé a bheith ina chúis le fadhb. Nuair a bhíonn luí daingean idir tolladh imthacaí agus seafta, molaimid duit trealamh preasa a úsáid le suiteáil.
Suiteáil aonad imthacaí

d. Tithíocht a réamh-ghéarú
Excessive tightening of the mounting bolts  may cause the housing to deform. Tighten the bolts to the proper torque, FK recommends using  a washer with the bolt when mounting the housing as the bolt alone may cause damage to the housing.
Tithíocht a réamh-ghéarú

e. Tighten setscrews
Insert a hexagonal bar wrench into the hexagonal hole of the setscrew, and tighten the setscrews with the recommended torque.
Níos doichte scriúnna tacair

f. Tighten housing
Excessive tightening of the mounting bolts  may cause the housing to deform. Tighten the bolts to the proper torque.
Níos doichte tithíocht

2. Mounting of eccentric locking collar unit:
NOTE:Eccentric locking collar unit is not recommended for applications where the direction of rotation is sometimes reversed, since the eccentric collar can loosen.
a. Install bearing unit

Avoid striking the bearing with a hammer to press-fit  the  bearing to the shaft,if  you give a strong impact to the side surface of the inner ring, the slinger moves, and it may cause a problem. When there is a tight fit between bearing bore and shaft, we suggest you use press equipment to install.
Suiteáil aonad imthacaí

b. Pre-tighten housing
Excessive tightening of the mounting bolts  may cause the housing to deform. Tighten the bolts to the proper torque , FK recommends using  a washer with the bolt when mounting the housing as the bolt alone may cause damage to the housing.
Tithíocht a réamh-ghéarú

c. Fit the eccentric collar
Fit the eccentric section of the inner ring of the bearing to the eccentric recessed section of the eccentric locking collar, and rotate the collar in the direction of shaft rotation by hands to tighten it temporarily.
Feistiú an coiléar eccentric

d. Rotate eccentric collar
Fit a rod in the hole on the circumference of the eccentric collar and tap it with a hammer so the collar rotates in the shaft rotating direction.
Rothlaigh coiléar eccentric

e. Tighten eccentric collar
Tighten the setscrew on the eccentric collar to the proper torque, please refer to FK catalog of the proper torque.
Níos doichte coiléar eccentric

f. Tighten housing
Excessive tightening of the mounting bolts  may cause the housing to deform. Tighten the bolts to the proper torque.
Níos doichte tithíocht

3. Mounting of adapter sleeve unit:
NOTE:The adapter sleeve unit can be reliably secured to the shaft even when it is subjected to the impact loads and vibrations. But, this unit can not be used on a shaft that is subjected to grease axial load.


a. Fit the sleeve onto the shaft
Fit the sleeve onto the shaft and position it so that its tapered section is centered to the bearing. For easy fitting, expand its slow with screwdriver or similar tools.
Cuir an muinchille ar an seafta

b. Install bearing units
Fit the bearing unit over the sleeve.
Suiteáil aonaid imthacaí

c. Pre-tighten housing
Excessive tightening of the mounting bolts  may cause the housing to deform. Tighten the bolts to the proper torque, FK recommends using a washer with the bolt when mounting the housing as the bolt alone may cause damage to the housing.
Tithíocht a réamh-ghéarú

d. Tighten adapter sleeve
Gently tap side of sleeve along the whole circumference of the sleeve so that the bearing inner ring is closely seated on the sleeve.
Níos doichte muinchille oiriúnaitheora

e. Fit washer and nut
Place the lockwasher, and fully handtighten the nut.
Feistiú washer agus cnó

f. Lock the nut
Fit a jig or a screwdriver in one of slots on the nut, and tap it with a hammer until the nut turns 60  to 90 degree. NEVER tap the slinger  and NEVER overtighten the nut.
Cuir an cnó faoi ghlas

g. Secure the nut
Bend tabs of lockwasher so that it fits into slots on the nut.
Never back rotate nut to fit washer tabs, forward rotate nut to fit the washer tabs.
Daingnigh an cnó

h. Tighten housing
Excessive tightening of the mounting bolts  may cause the housing to deform. Tighten the bolts to the proper torque.
Níos doichte tithíocht

4. Mounting of  unit with covers:
a. Fill grease
In order to enhance dust and waterproofing effects, apply grese all around the seal lip of the cover, and fill the 2/3 internal space of the cover with grease.
Líon ramhar

b. Install bearing unit
Pass one cover along the shaft, then slide the bearing unit onto the shaft.  The steps to install bearing unit onto the shaft is same as the mounting steps setscrew unit. It is recommended that the end of the shaft be chamfered beforehand to avoid damaging the lips of the rubber seal.
Suiteáil aonad imthacaí

c. Fit cover 1
Tóg an clúdach atá rite feadh an seafta agus brúigh isteach sa tithíocht é. Bí cúramach gan dromchla an chlúdaigh a bhualadh go díreach le casúr cruach ach bain úsáid as roisín sintéiseach nó bloc adhmaid. Ó threo 45 céim, sconna timpeall imlíne an chlúdaigh chun tionchar aonfhoirmeach a imirt ar an gclúdach chun é a fheistiú sa groove ar an tithíocht.
Clúdach oiriúnach 1

d. Clúdach oiriúnach 2
Bí cúramach gan dromchla an chlúdaigh a bhualadh go díreach le casúr cruach ach bain úsáid as roisín sintéiseach nó bloc adhmaid. Ó threo 45 céim, sconna timpeall imlíne an chlúdaigh chun tionchar aonfhoirmeach a imirt ar an gclúdach chun é a fheistiú sa groove ar an tithíocht.
Clúdach oiriúnach 2